A lot of people now wonder how it could be made possible. It is not very easy if you are a kind of person who is resourceful. This article aims to help you. There are instructions below you could follow on how to do it. You need all the equipment for you to start. Otherwise you cannot start doing them without the necessary stuff you need.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Once you have it already, then get a thermometer and also a timer. These two could be use to determine you their temperature. Oven toasters have their own timer, but you would be using one to check the pcb. If they are hot enough already.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
Add flux. This is used for modification purposes. And it can also be used as a marker So it would be easy to identify the things you put in there. So all the balls will stay in their designated location. Only apply the flux on top of the board and not to somewhere else.
Align the components. You need to do this, so it will be easy for you to recognize them and identify all the parts. And put them inside the oven. Make sure that you can clearly see the activities inside so you can monitor them. If you have a silk screen, use it for the alignment. It is the advise of most experts.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
And come back again to check if the experiment is a success. And see if everything are connected. Especially the balls since they are the most important. If all are connected, it only means that you did a great job.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Once you have it already, then get a thermometer and also a timer. These two could be use to determine you their temperature. Oven toasters have their own timer, but you would be using one to check the pcb. If they are hot enough already.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
Add flux. This is used for modification purposes. And it can also be used as a marker So it would be easy to identify the things you put in there. So all the balls will stay in their designated location. Only apply the flux on top of the board and not to somewhere else.
Align the components. You need to do this, so it will be easy for you to recognize them and identify all the parts. And put them inside the oven. Make sure that you can clearly see the activities inside so you can monitor them. If you have a silk screen, use it for the alignment. It is the advise of most experts.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
And come back again to check if the experiment is a success. And see if everything are connected. Especially the balls since they are the most important. If all are connected, it only means that you did a great job.
About the Author:
When you are searching for the facts about a reflow soldering oven, go to our website today. More details can be seen at http://www.sikama.com now.
ليست هناك تعليقات:
إرسال تعليق